oil based epoxy floor paint

Issue 1: Surface Wrinkles and Bubbles After Application  Cause Analysis: ① The base layer moisture content exceeds the standard (>8%), causing evaporation and bubbles after application; ② The colored sand and curing agent are not mixed evenly, resulting in trapped air; ③ The application temperature is too low (<10°C), resulting in a slow curing process and wrinkling.  Solution:  Small Area (<10cm²): After the floor is fully cured (7 days), use a utility knife to open the bubbles and remove any impurities. Fill the gaps with a water-based epoxy repair agent and the same colored sand. After drying, sand the surface smooth and apply a topcoat.  Large Area: If the area with bubbles or wrinkles exceeds 10% of the total surface area, remove the floor, reapply two coats of moisture-proof primer to the base layer, and then apply the standard process.  Issue 2: Color variation after curing, with areas showing varying shades.  Cause Analysis: ① Mixing different batches of colored sand during construction (natural colored sand has slight color variations between batches); ② Uneven application of topcoat, resulting in darker areas with thicker coating; ③ Significant color variation in the base layer (e.g., areas previously painted), causing color variation due to color bleed-through.  Solution:  Minor color variation (not noticeable to the naked eye): Apply a coat of epoxy wax to the entire surface, using the wax's covering power to minimize the color variation.  Significant color variation: For lighter areas, apply a thin coat of diluted topcoat of the same color (diluted with water in a 1:1 ratio, applied thinly). After drying, compare the colors until they are consistent with the surrounding areas.  Issue 3: Delamination at edges or corners after six months of use.  Cause Analysis: ① Edges, such as corners and doorways, were not reinforced, resulting in delamination from prolonged foot traffic and friction; ② Primer was not applied to the edges during construction, resulting in poor adhesion; ③ Ground subsidence caused cracks in the base layer, leading to delamination. Solution: Local delamination (small area): Scrape off the delamination, sand the base, and apply a coat of primer. Fill the gap with water-based epoxy putty and sand of the same color. After drying, apply a topcoat. Mask the edges with masking tape to ensure a clean line.  Delamination caused by cracked base: First, repair the cracks in the base (using cement mortar). After drying, repair the floor according to the above steps.  Issue 4: Colored sand particles have fallen off, leaving "pits" on the surface.  Cause Analysis: ① The purchased colored sand has poor compatibility with the resin (low-quality colored sand has an uneven surface, making it difficult to bond with the resin); ② The ratio of colored sand to curing agent was incorrect during application (too little curing agent, so the resin was not fully cured); ③ Prolonged friction with sharp objects caused particles to fall off. Solution: Small pits: Use a toothpick to apply a small amount of water-based epoxy glue and fine sand of the same color to fill the pit. After drying, sandpaper to smooth the gap.​ Large areas of loose particles: Partially scrape away and then reapply the middle layer of colored sand. Choose colored sand from the same brand and batch as the original product to avoid compatibility issues.

Commercial floors are more than just "ground"—they're an extension of your brand image. water-based epoxy colored sand floor paint, with its customizable texture and environmentally friendly properties, has become a popular choice for shopping malls, cafés, and offices. However, the needs of different commercial settings vary greatly—shopping malls need "eye-catching," cafés need "atmosphere," and offices need "practicality." Today, we'll share specific stylizing tips for each.  1. Shopping Malls and Stores: Attract Customers with "Differentiated Textures"  Core Requirements: Highlight the brand's style while withstanding the wear and tear of high foot traffic (thousands of people per day).  Styling Options:  Fast fashion stores (such as clothing and accessories stores): Choose 0.5mm fine sand, primarily in pure white or light gray. Pair with a highly reflective water-based topcoat (with a mirror effect in some areas) to enhance the space's brightness and highlight the product colors. Cultural and Creative Handmade Stores: Choose 1-1.5mm coarse sand in Morandi colors (such as grayish pink and light green). Preserve the original texture of the sand and pair it with wooden shelves to create a "handmade" feel that complements the merchandise. Entrance Area: Choose 1.5-2mm coarse sand (anti-slip coefficient ≥ 0.6) to prevent customers from slipping in rainy weather. A "brand logo inlay" design (using different colored sand colors to create a logo) can be used to enhance recognition.  2. Cafes: Create a check-in atmosphere with a "textured" feel  Core Need: Create a "photography" atmosphere while ensuring easy cleanup after coffee spills.  Matching Options: Industrial Cafes: Choose 2mm coarse sand in cement gray and dark brown to preserve the rough texture of the sand particles. Paint the walls with cement paint and pair them with wrought iron tables and chairs to create a "retro warehouse" atmosphere. Copper strips can be embedded in the floor to separate areas. For a Japanese-inspired, relaxing cafe: Choose 0.3mm fine sand, using off-white or light wood tones, paired with a matte finish. Use irregular color blocks (e.g., off-white + light brown) for the floor. Add rattan chairs and greenery to reduce the commercial feel.  Details: The floor under the bar can be treated with a splash-proof finish (two coats of water-based finish) to prevent coffee stains from seeping through the gaps in the sand.  3. Office: Balance practicality and simplicity to improve work efficiency  Core requirements: The floor should be quiet (no noise when walking), stain-resistant (avoid frequent cleaning that disrupts work), and maintain the clean aesthetic of the space.  Styling options:  Open office area: Choose 0.5mm fine sand, using light gray or light blue (low-saturation colors can reduce visual fatigue), paired with a matte finish. Keep the floor clean and uncluttered. Conference Room/Reception Area: Choose a medium-sized sand particle size of 0.8mm and a dark gray or navy blue color (for a formal look). Create "line dividers" (using a darker shade of the same color) on the floor to demarcate seating areas.  Painter Room: Choose a coarse sand particle size of 1mm and a light brown color (for stain resistance). Create a slight slope (0.5%) on the floor to prevent water accumulation and ensure a satisfactory anti-slip coefficient.

  When it comes to flooring, it's often difficult to balance environmental considerations with practicality. However, water-based epoxy colored sand floor paint breaks this deadlock. It combines the natural texture of colored sand with the low-toxicity of water-based paint, making it a new favorite in the recent renovation market. Today, let's take a 5-minute look at this flooring material that boasts aesthetic appeal, performance, and environmental friendliness.  1. Definition: More than just a "floor," it's a combination of environmental friendliness and aesthetic quality.  Water-based epoxy colored sand floor paint uses a water-based epoxy resin as a base, blended with natural colored sand (such as quartz sand or colored jade sand), and a water-based hardener. It creates a granular, textured floor coating by brushing or scraping. Compared to traditional solvent-based epoxy flooring, it requires no organic solvents for dissolution and has an extremely low VOC content. Compared to ordinary epoxy colored sand, it retains the anti-slip and wear-resistant properties of colored sand while being easier to apply and having less odor.  2. Core Features: Three Key Advantages Address Renovation Pain Points  Environmentally Friendly and Safe: VOC content is ≤100g/L (far below the national standard of 200g/L), resulting in no pungent odor during application and no release of formaldehyde or benzene after curing. It is suitable for sensitive areas such as children's rooms, elderly rooms, and schools.  Unique Texture: The colored sand particles are clearly visible (particle size optional, 0.1-2mm), creating a matte or semi-matte finish, eliminating the cold, mirror-like appearance of traditional flooring and providing a natural texture.  Durable and Durable: With a surface hardness of 2-3H, it is resistant to abrasion and impact. The colored sand is tightly bonded to the resin, resisting fading and delamination. It is particularly suitable for high-use areas such as kitchens, hallways, and garages.  3. Common Misconception: Don't Confuse It with "Ordinary Colored Sand Flooring"  Many people believe there's no difference between water-based epoxy and solvent-based epoxy. In fact, there are significant differences: water-based epoxy can be diluted directly with water during application, eliminating the need for a gas mask; solvent-based epoxy requires solvents like banana oil, which can have a strong odor and requires ventilation for at least a week. Furthermore, water-based epoxy is more flexible after curing and less prone to cracking due to temperature fluctuations, making it more suitable for colder northern regions.

Construction period range: 1.Conventional period: Usually 15-20 days are required to complete all processes. 2. Special epoxy terrazzo process: Some complex processes (such as epoxy gold terrazzo) require more than 20 days. 3.The curing time can be shortened to 48 hours in summer and extended to 24-48 hours in winter.  Key construction stages: Base preparation (2-3 days): Including cleaning, leveling and epoxy primer application. The moisture content must be controlled below 8%.  Surface paving and curing: After paving, the epoxy terrazzo layer needs to be cured for 24-48 hours (summer) or longer (winter). Inorganic terrazzo curing takes 7-10 days. Epoxy terrazzo curing takes shorter time but the process is more complicated. Grinding and polishing (3-5 days) It is divided into coarse grinding (diamond No. 60-90), fine grinding (No. 200-500), and fine grinding (No. 2000-3000) processes.  Finishing treatment (1-2 days) Including grouting, waxing and finished product protection.  Influencing factors Temperature: The curing time may be extended by more than 50% in winter. 12 Process complexity: Epoxy grindstone requires multiple repairs and layered curing, which takes 5-7 days longer than inorganic grindstone.

Material Composition   Traditional terrazzo uses Portland cement or white cement as a binder, mixed with aggregates such as crushed stone, glass, and quartz, and then ground and polished to create a surface. Epoxy terrazzo uses a modified epoxy resin as a binder, allowing it to incorporate a wider variety of aggregates (such as natural marble and quartz) and achieve seamless integration.   Performance Crack Resistance: Epoxy terrazzo's tough polymer material reduces the risk of cracking in temperature fluctuations. Traditional terrazzo, due to its high coefficient of expansion, is susceptible to cracking due to thermal expansion and contraction.   Stain Resistance: Epoxy terrazzo's dense surface resists stains and is easy to clean and maintain. Traditional terrazzo's porous structure easily accumulates stains and requires regular crystallization.   Wear Resistance: Epoxy terrazzo offers excellent compressive and flexural strength, with a service life of up to 10 years. Traditional terrazzo is prone to sanding and cracking, and lacks durability under frequent use. ‌   Color Performance‌: Epoxy terrazzo uses color paste to create richer, more vibrant colors; traditional terrazzo relies on pigments, resulting in a monotonous color. ‌   Applicable Scenarios   Epoxy terrazzo is suitable for high-end commercial spaces (such as shopping malls and hotels) due to its high decorative properties and durability. Traditional terrazzo, being economical, is often used in public facilities such as schools and hospitals.

If you want to learn more about oil based retro floor paint, from product characteristics to purchase points, to market trends, every aspect is worth exploring in detail. Core product features Rich texture effects: A highlight of retro floor paint is that it can present a variety of realistic texture effects. Through special formulas and advanced construction processes, it can simulate the aging effect of cement, from slight wear marks to severe cracking and peeling, which can be vividly displayed, as if the ground has really experienced decades of polishing. For metal rust effects, it can accurately restore the color layers and mottled texture of rust, from dark red to brown and yellow, to black rust, making the ground look like a piece of metal plate that has experienced wind and rain. Retro floor paint with imitation stone texture is also not inferior, whether it is the delicate texture of marble or the rough grain of granite, it can be perfectly reproduced. Excellent physical properties: Retro floor paint performs well in physical properties. Its high wear resistance enables it to withstand frequent daily trampling and furniture movement, and it can maintain a good appearance for a long time in commercial places with large traffic, as well as living rooms, corridors and other areas in the home. Good impact resistance means that even if heavy objects accidentally fall, the ground is not easy to be damaged. In some factory workshops, the use of retro floor paint not only meets the requirements of industrial production for ground strength, but also adds a unique retro style to the workshop. In addition, it has strong chemical corrosion resistance and can effectively resist common stains and liquid erosion, such as coffee stains, oil stains, water stains, etc. Environmental protection performance: With the continuous improvement of people's environmental awareness, the environmental protection requirements for decoration materials are becoming more and more stringent. Most high-quality retro floor paints are produced with environmentally friendly materials, and strict control is exercised in the selection of raw materials. Raw materials containing harmful substances such as benzene and formaldehyde are not used. In the production process, advanced technology is used to reduce the emission of pollutants. In addition, these products have passed relevant environmental protection tests and obtained corresponding environmental protection certifications, such as China Environmental Labeling Product Certification. This means that after using retro floor paint for floor decoration, it will not have a negative impact on indoor air quality, and can protect the health of residents or users. For families with elderly people and children, or places such as schools and kindergartens, it is particularly important to choose environmentally friendly oil based retro floor paint. ​

Water-based epoxy colored sand topcoat can shine in various scenes with its diverse performance and rich expressiveness. The following practical application cases in different scenes will take you to intuitively feel its charm and practicality. 1.Warm home scene: create a comfortable living space  Living room wall decoration In a modern and simple living room, choose light gray water-based epoxy colored sand topcoat with white plaster line to create a simple and atmospheric atmosphere. The delicate texture of colored sand flickers slightly under the light, adding a sense of refinement to the space. The TV background wall uses dark gray water-based epoxy colored sand topcoat, which is treated with a special roughening process to create a unique texture, making it the visual focus of the living room. Whether it is a family gathering or daily leisure, such a wall can make people feel comfortable and cozy. Children's room wall design The wall of the children's room should be colorful and environmentally friendly and safe. Choose a pink water-based epoxy colored sand topcoat, paired with hand-painted cartoon patterns, to create a dreamy growth space for your children. Its excellent stain resistance allows children to give full play to their imagination and graffiti on the wall, and parents do not need to worry about it being difficult to clean. Moreover, the environmental performance of water-based epoxy colored sand topcoat can escort the healthy growth of children. 2. Commercial space scene: enhance brand image Internet celebrity coffee shop wall decoration A Internet celebrity coffee shop that focuses on retro industrial style uses dark brown water-based epoxy colored sand topcoat on wall decoration, and creates a texture of years of precipitation through aging treatment. The exposed red bricks and dark walls complement each other, and with warm yellow lights, they instantly attract the attention of customers and become a popular check-in point. The wear-resistant and stain-resistant performance of water-based epoxy colored sand topcoat can also cope with the frequent flow of people and friction between tables and chairs in the coffee shop, keeping the wall beautiful for a long time. Brand store wall design In order to highlight the elegance and fashion sense of the brand, a fashion women's clothing store chose off-white water-based epoxy colored sand paint as the main color of the wall, matched with golden decorative lines, to create a high-end shopping environment. In the display area, colorful water-based epoxy colored sand paint is used to create a unique background wall, which complements the displayed clothing, effectively improves the display effect of the goods, and enhances the customer's desire to buy. 3.Industrial site scene: achieve efficient protection Factory workshop wall protection In the mechanical processing workshop, the wall is often polluted and collided by oil, iron filings, etc. The stain resistance and wear resistance of water-based epoxy colored sand paint play an important role here. The use of gray water-based epoxy colored sand paint can not only effectively resist the erosion of oil and iron filings, but also its high-strength paint film can prevent the wall from being damaged by equipment collision, reducing the maintenance cost and frequency of the wall, and creating a clean and safe production environment for the factory. Warehouse wall treatment The handling and storage of goods in the warehouse can easily cause wear and tear on the wall. Using water-based epoxy colored sand topcoat for wall treatment can greatly improve the wear resistance and scratch resistance of the wall. At the same time, its stain resistance also facilitates daily cleaning and keeps the warehouse wall clean. Moreover, water-based epoxy colored sand topcoat can choose different colors according to the functional divisions of the warehouse, which is convenient for the classification and management of goods and improves storage efficiency. From warm homes to bustling commercial spaces to busy industrial sites, water-based epoxy colored sand topcoat has shown strong adaptability and practicality. Have these practical application cases brought you new inspiration? If you also have decoration needs for specific scenes, please share and discuss more exciting application solutions together!

1. Environmental regulations are becoming stricter: The green gene of water-based epoxy is a pass Water-based epoxy uses water as a diluent, and its emissions are much lower than traditional oil-based epoxy, which can easily meet the increasingly stringent global and local environmental regulations to avoid fines and shutdown risks. Environmentally friendly construction: There is no obvious irritating odor, which greatly improves the operating environment of workers. It is especially suitable for sensitive places such as hospitals, schools, shopping malls, and office buildings that need to be operated while being renovated. 2. Pain points of renovation construction: Water-based epoxy provides efficient solutions Stronger adaptability to wet substrates: Renovation projects often face incomplete drying of the base layer (such as underground environments and old buildings). Water-based epoxy has excellent wet adhesion and can be well cured on wet substrates. Excellent recoating performance: For common local repairs or future renovations, water-based epoxy has good interlayer adhesion, saving time and effort. Convenient and safe construction: Tools can be directly washed with water, making construction more convenient; non-flammable, safer to store and transport. 3. Excellent performance: meet the stringent use requirements after renovation Tough and wear-resistant: Modern water-based epoxy technology is very mature, and its physical and mechanical properties (hardness, wear resistance, impact resistance) are comparable to or even exceed some oil-based products. Excellent adhesion: It has good adhesion to a variety of common renovation base surfaces (concrete, terrazzo, old epoxy coatings, tiles, etc. Good chemical resistance: It can resist the erosion of daily detergents, grease, weak acids and alkalis, and is easy to clean and maintain. Beautiful and diverse: It provides different glosses such as matte and gloss, with rich and stable colors.

In the modern transportation system, clear and eye-catching road markings are important infrastructure to ensure traffic safety. Whether it is the hustle and bustle of the city or the traffic in the countryside, road markings are like silent guides, guiding vehicles and pedestrians to pass in an orderly manner. Among the many road marking materials, water-based acrylic road marking paint has gradually become a "star product" in the field of road marking with its unique performance and environmental advantages. 1. The core advantages of water-based acrylic road marking paint Excellent environmental performance Traditional solvent-based marking paint releases a large amount of volatile organic compounds (VOCs) during production and use. These substances not only threaten the health of construction workers, but also aggravate air pollution, form photochemical smog, and harm the ecological environment. Water-based acrylic marking paint uses water as a solvent, contains almost no organic solvents, and has extremely low VOCs emissions. It meets the requirements of national environmental protection policies and is a typical representative of green and environmentally friendly coatings. During the construction process, there is no pungent odor, which can effectively improve the construction environment and reduce the impact on surrounding residents and ecology.​ Excellent physical properties​ Water-based acrylic marking paint has good wear resistance and weather resistance. Road markings are exposed to the outdoors for a long time, and are subjected to frequent vehicle rolling, sun and rain, wind and snow erosion, etc. Ordinary paints are prone to wear and fading. With its special formula and molecular structure, water-based acrylic marking paint can form a tough paint film on the road surface. Even on roads with heavy traffic, it can remain clear and complete for a long time, greatly reducing the maintenance frequency and cost of road markings. In addition, the marking paint also has excellent adhesion and can firmly adhere to a variety of road substrates such as cement and asphalt, and is not easy to peel off. ​ Fast drying speed​ In road construction, time is efficiency. The fast drying speed of water-based acrylic marking paint gives it a significant advantage in practical applications. Under normal circumstances, it can be dry on the surface 10-30 minutes after construction at room temperature, and it can be completely dry in 1-2 hours, which greatly shortens the construction time and reduces the impact of road closures on traffic. It is particularly suitable for places such as urban roads and airport runways that have strict requirements on construction time.​ 2. Wide application areas​ Road traffic markings​ On urban roads, highways, national and provincial roads and other types of roads, water-based acrylic marking paint is an ideal material for marking traffic lines. It can clearly mark lane demarcation lines, edge lines, guide arrows, pedestrian crossing lines, etc., provide clear traffic guidance for drivers and pedestrians, regulate traffic order, and reduce the occurrence of traffic accidents. At the same time, its good reflective performance can make the markings clearly visible at night or in low light conditions, further ensuring driving safety. ​ Parking lot and garage markings​ Parking lots and garages are concentrated areas for vehicle parking. The clarity of the markings directly affects the parking efficiency and safety of vehicles. Water-based acrylic marking paint can be used to divide parking spaces, lane lines, entrance and exit indicator lines, etc., which can not only make the parking lot layout more reasonable and orderly, but also guide vehicles to park accurately through eye-catching colors and clear lines to avoid scratch accidents. In addition, its environmental protection characteristics also meet the use requirements of relatively closed spaces such as parking lots and garages.​ Sports field marking lines In various sports venues, such as basketball courts, tennis courts, football fields, etc., water-based acrylic marking paint is used to divide the boundaries of the venue, regional markings, etc. It has the characteristics of bright colors and long-lasting non-fading, which can provide athletes with clear venue boundaries and ensure the fairness and standardization of the competition. At the same time, good wear resistance and anti-slip properties can meet the needs of athletes in high-intensity sports and reduce the risk of sports injuries. ​ Other fields In addition to the above main application scenarios, water-based acrylic marking paint can also be used for factory workshop floor markings, school playground markings, commercial area sidewalk markings and other fields, providing clear and durable marking services for different places. ​ 3. Scientific construction methods Preparation before construction Before construction, the road surface needs to be thoroughly cleaned to ensure that the road surface is dry, clean, free of oil, dust and other impurities. Loose particles and attachments on the road surface can be removed by sweeping with a broom, washing with a high-pressure water gun or mechanical grinding. At the same time, check the flatness and roughness of the road surface. For uneven roads, repairs should be carried out to ensure the quality of the marking. In addition, it is necessary to prepare the equipment required for construction, such as marking machines, paint mixers, spray guns, etc., and debug the equipment to normal working conditions. ​ Preparation of paint​ According to the requirements of the product manual, mix the water-based acrylic marking paint with an appropriate amount of water and stir evenly. The amount of water added during the preparation process must be strictly controlled. Too much or too little will affect the performance and construction effect of the paint. At the same time, according to actual construction needs, an appropriate amount of reflective glass beads can be added to improve the reflective performance of the marking. When adding glass beads, they should be added evenly during the mixing process of the paint to ensure uniform dispersion. ​ Construction process​ When using a marking machine for construction, the parameters of the marking machine, such as nozzle size, paint flow, driving speed, etc., should be adjusted according to the width and shape of the marking line. During the construction process, the marking machine should be kept at a constant speed to avoid speed fluctuations or pauses in the middle to ensure uniform thickness and straight lines. For some complex marking patterns or irregular areas, a spray gun can be used for manual re-marking to ensure the integrity and accuracy of the markings. After the construction is completed, the construction equipment should be cleaned in time to avoid the paint from drying and clogging the equipment. ​ Maintenance after construction​ After the construction is completed, before the markings are completely dry and solidified, warning signs should be set up to prohibit vehicles and pedestrians from passing through to avoid damage to the markings. At the same time, pay attention to weather changes to avoid being affected by bad weather such as rain and sun exposure in a short period of time after construction. Generally, it takes about 24 hours for the markings to completely dry and solidify. During this period, the protection and inspection of the markings should be strengthened, and problems should be dealt with in a timely manner. ​ 4. Future development trends​ With the continuous improvement of people's environmental awareness and the increasingly stringent national environmental protection policies, the market demand for water-based acrylic marking paint will continue to grow. In the future, this product will develop in the direction of high performance and multi-functionality. For example, by improving the formula and production process, the wear resistance, water resistance, chemical corrosion resistance and other properties of the coating can be further improved; new water-based acrylic marking paints with self-repairing, self-cleaning, anti-skid and noise reduction functions can be developed to meet the special needs of different scenarios. At the same time, with the continuous development of intelligent construction equipment, the construction efficiency and quality of water-based acrylic marking paints will also be further improved, promoting the road marking industry to move towards a more intelligent and automated direction. ​ Water-based acrylic road marking paints play an increasingly important role in the field of road markings due to their environmental protection, excellent performance, and wide application. Whether it is to ensure traffic safety or to enhance the image of the city, it has made an indelible contribution. I believe that in the future, with the continuous advancement and innovation of technology, water-based acrylic marking paints will bring more convenience and safety to our lives.

As a traditional floor coating, oil-based floor paint still occupies an important position in specific fields due to its unique properties. The following is an analysis of its core advantages and applicable scenarios: 1. Excellent physical properties Due to the addition of organic curing agent, the paint film hardness of oil-based floor paint can reach a high level (such as 2H standard), and its wear resistance and compression resistance are particularly outstanding, which is suitable for heavy-duty industrial areas such as logistics warehouses, mechanical workshops, etc. Its high-gloss surface can also enhance the beauty of the floor and is suitable for commercial spaces that require visual effects. 2. Mature technology and construction experience After years of development, the construction process of oil-based paint has been widely mastered. Experienced construction teams can complete the coating quickly and have more flexibility in handling complex base surfaces. 3. High cost-effectiveness In terms of material cost, oil-based paint is usually lower than water-based floor paint, especially the topcoat part. For projects with limited budgets and low environmental requirements, oil-based paint is more economical. 4. Stable chemical resistance Oil-based paint has strong tolerance to oil and chemical solvents, and is suitable for environments that are easily exposed to corrosive substances, such as auto repair shops and chemical plants. 5. Irreplaceable application scenarios Although environmental protection policies are becoming stricter, oil-based paint is still irreplaceable in the following scenarios: Environment with high humidity or large temperature difference: Oil-based paint has strong penetration and can adapt to some wet base surfaces. Short-term high-frequency use requirements: such as temporary exhibition halls or rapid renovation projects, because it can be put into use after drying.      

BestRich unique technology of water-based epoxy floor paint are：   1.Our factory's latest research has launched a new epoxy water-based floor paint, which can replace the oil-based floor paint of primer and intermediate paint. The price is more favorable, healthier and environmentally friendly.    2.Water-based epoxy floor paint can reach 80 degrees without the need for topcoat, reducing costs.   3.BestRich water-based epoxy floor paint does not soften when applied thickly, and 10 cm thick application can also dry quickly, allowing you to work efficiently.   4.After the normal construction of BestRich water-based epoxy floor paint is completed, it can withstand the rolling of forklifts and cars. It has high hardness and its hardness can reach 3H or above.   5.BestRich water-based epoxy floor paint has better leveling properties, and normal construction will not produce roller trowel marks or joint marks.  

Compared with oil-based epoxy floor paint, water-based epoxy floor paint has the following advantages:   ‌Better environmental protection‌: Water-based epoxy floor paint uses water as solvent, does not contain harmful substances, is non-toxic and odorless, does not volatilize pungent odor, and has less harm to the environment and human health‌. Oil-based epoxy floor paint uses organic solvents, which will release irritating odors during construction and are toxic substances. They are flammable and explosive items during transportation‌.   ‌Wider scope of application‌: Water-based epoxy floor paint can be used in humid environments and is suitable for underground parking lots, hospitals, schools and other places‌. Oil-based epoxy floor paint requires a dry construction environment and is not suitable for humid places‌.   ‌Better air permeability and moisture resistance‌: Water-based epoxy floor paint has good air permeability, can adapt to slight changes in the base layer, is not prone to blistering, cracking and other problems, and is suitable for damp or re-humid environments‌. Oil-based epoxy floor paint is permeable Poor air resistance, prone to blistering, delamination and other quality problems due to moisture in the base layer ‌.   ‌Higher construction efficiency ‌: Water-based epoxy floor paint primer and midcoat can be diluted with water, which is relatively simple to construct, and the ingredients are not very thick, so the construction efficiency is high ‌. ‌Although the construction process of oil-based epoxy floor paint is proficient, it has high requirements for the construction team and rich experience in handling on-site construction problems ‌.   ‌Excellent physical properties ‌: The hardness of water-based epoxy floor paint can reach more than 2H, and it has the same or higher physical properties as oil-based epoxy ‌. ‌Although oil-based epoxy floor paint has good wear resistance, the paint film is hard and brittle and easy to damage ‌.   ‌Higher cost-effectiveness ‌: Although the material cost of water-based epoxy floor paint is high, the labor cost is relatively low due to high construction efficiency ‌. ‌Oil-based epoxy floor paint has a low price, but the environmental protection problems and subsequent maintenance costs during construction are high ‌.